Insulating Glass Units
FSGLASS's insulating glass units are Insulating Glass Certification Council (IGCC) certified to ASTM E2190 Standard Specification for Insulating Glass Unit Performance and Evaluation.
Laminated Glass Units
FSGLASS's laminated glass units with a minimum .030" pvb interlayer comply with ANSI Z97.1 and CPSC 16 CFR 1201, which are the industry safety standards for glazing materials. In addition, FSGLASS’s laminated glass units comply with ASTM 1172 Standard Specification for Laminated Architectural Flat Glass.
Edge Blushing - In both structural and butt glazed applications, silicone sealants may come in contact with the polyvinyl butyral (pvb) interlayer used in laminated glass. When silicone contacts the laminated glass edge, a cosmetic blushing of the pvb interlayer will occur over time. It generally begins as a small bubble formation at the contacted edge, which then grows to form a limited unbonded area at the glass edge. This reaction is limited and generally does not exceed more than 3/8" (9.5mm). Edge blushing may be visible however does not affect the structural integrity of the laminated glass with respect to its ability to resist uniform loads.
Coated Glass - Low-E or Reflective
FSGLASS's coated glass products comply with ASTM Standard C1376 Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass.
- Pinholes: Inspect glass from a distance of 10 ft. (3m) in transmission, at a viewing angle of 90° to the specimen, against a bright uniform background. If a pinhole is readily apparent, the following criteria apply: Pinholes larger than 1/16" (1.6mm) in diameter are not allowed in 80 percent of the central glass area. Pinholes larger than 3/32" (2.4mm) are not allowed in the outer 20 percent of the glass area. No more than two readily apparent blemishes are allowed in a 3" (75mm) diameter circle and no more than five readily apparent blemishes are allowed in a 12" (300mm) diameter circle.
- Uniformity: When viewing coated glass from a minimum distance of 10 ft. (3m), color variation may occur from one unit to another. This can be caused by variations within the float glass substrate and normal production variations, and this is not considered a defect. All FSGLASS commercial glass products conform to industry color standards.
- Distortion: Various factors involved in heat processing, insulating air spacers and frame binding may distort reflected objects viewed on the glass surface. These are not considered defects of the coated glass or the final fabricated product.
- Scratches: Inspect glass from a distance of 10 ft. (3m). Scratches up to 2" (50mm) are allowed in 80 percent central glass area, and scratches up to 3" (75mm) are allowed in the outer area. Concentrated scratches or abraded areas are not allowed.
Digital Printing Glass
FSGLASS’s Digital Printing glass products comply with ASTM C1048 Standard Specification for Heat Strengthened and Fully Tempered Flat Glass – Kind HS, Kind FT Coated and Uncoated, Condition B.
View Digital Printing glass from a distance of 10 ft. (3m) with light reflected from the exterior surface. The glass should be placed against a uniform, opaque background in a vertical position.
Variations in perceived color may occur with any ceramic ink and will be more apparent with white or light colors because of unavoidable light transmission. Due to the inherent variations in ceramic ink thickness, light colors are more readily influenced by the colors of the materials installed behind the glass. FSGLASS takes no responsibility for variations in color or thickness that are within quality standards.
When viewing Digital Printing glass under similar conditions, pinholes, fisheyes, color concentrations, streaks from the printing process and paint particles are not defects.
Patterns or images may be located up to 1/16" (1.6mm) off parallel from the locating glass edge. Patterns or images may be up to 1/8" (3mm) off parallel from edges other than the locating glass edge.
An indefinite border of up to 1/32" (0.8mm) is acceptable.
For Digital Printing Dual Image, the stacking tolerance is 0.002" maximum between dot axis centers. The darker colored dot may be 0.005" larger in diameter than the lighter colored dot. Dots of identical diameters will still conform to the stacking tolerance.
Variation of +/-1/32" (0.8mm) in pattern or image location is acceptable.
Printing to Edge of Glass
There will be a 2mm nominal clear, enamel-free border around all edges for glass without a coating.
Digital Printing in combination with a Low-E coating, requires a minimum 3/8” (9.525mm) clear, enamel-free border around all edges. Some products require a wider enamel-free border, contact FSGLASS for details.
FSGLASS’s silk-screened glass products comply with ASTM C1048 Standard Specification for Heat Strengthened and Fully Tempered Flat Glass – Kind HS, Kind FT Coated and Uncoated, Condition B.
View silk-screened glass from a distance of 10 ft. (3m) under natural daylight conditions. Pinholes larger than 1/16” (1.6mm) are not allowed if noticeable from a distance of 10 ft. or greater. Color as well as opacity of the ceramic frit pattern may vary slightly due to paint thickness variations.
- Pattern Orientation: Patterns may be located up to 1/16” (1.6mm) off parallel from the locating glass edge. Due to glass dimensions and squareness tolerances, patterns may be up to 1/8” (3mm) off parallel from edges other than the locating glass edge.
- Pattern Definition: a print definition of 1/32” (0.8mm) indefinite border is acceptable.
- Pattern Registry: Maximum variation of +/- 1/32” (0.8mm) in dot, line or hole location is acceptable.
- Full Coverage Translucent Frit:
- Pinholes to 1/16” diameter, fisheyes, streaks from screening process and paint particles are allowed. Large clusters of close spacing of pinholes or other defects are not allowed in the central 80% of the glass area.
- Color and uniformity may vary slightly due to variations in ceramic frit thickness.
- Approval of a full-size mock-up at an 11-foot inspection distance and a 90-degree angle to glass surface against a bright uniform background is required.
- Not for use in interior applications
- Spandrel cavities may be prone to condensation formation on the glass surface exposed to the cavity. Over time, this may result in a visible film formation. Therefore, translucent frit should be applied to a surface not exposed to the spandrel cavity.
FSGLASS’s spandrel glass products comply with ASTM C 1048 Standard Specification for Heat Strengthened and Fully Tempered Flat Glass – Kind HS, Kind FT Coated and Uncoated, Condition B.
View spandrel glass from a distance of 15 ft. (4.6m) under natural daylight conditions. Color and reflectance may vary when viewed under a uniform, opaque background. This is not considered a defect.
When viewing spandrel glass under similar conditions, reflected pinholes and scratches are not considered defects if they are unobtrusive.
In structurally glazed applications, a clear edge may be visible. Contact FSGLASS's Sales Department for more information.
FSGLASS reserves the right to change substrate glass suppliers. As a result, this may affect perceived colors of our Viraspan samples. Approval of all glass colors is based on 12" x 12" (305 mm x 305 mm) samples, which are ordered for each project.